Problem Proton UR500 sur Pad 24

[ovrocm]

Hi,

The scenario instructions (document Pack24En.pdf), states the following:

“For the train (ProtonTrain) the initial position is in the center of the launching pad to the foot of the rocket
.
.
.
.

The rocket can be released by doing Ctrl + Q followed by Shift + 0 on the numeric keypad It can be reloaded if the support is erected against it by performing the same maneuver”



The problem is that the key sequence, Ctrl + Q, suggested to release the rocket from the train is the same one used to exit simulation.

Every time this key sequence is used, instead of releasing the train it simply exits the simulation.

Regards

 

[n72.75]

What version of Orbiter are you using?

 

[MaxBuzz]

proton ready to launch (no train)

ProtonKrotonUR500/ProtonK
STATUS Landed Earth
POS 62.9847654 46.0709434
HEADING 359.68
ALT -0.077
AROT 49.364 -18.369 160.157
RCSMODE 2
AFCMODE 7
FUEL 1.000
NAVFREQ 0 0 0 0
XPDR 0
CONFIG_FILE Config\Vessels\ProtonUR500\Mir\Priroda.ini
GUIDANCE_FILE Config\Vessels\ProtonUR500\Mir\Mir.txt
CONFIGURATION 0
CURRENT_BOOSTER 1
CURRENT_STAGE 1
CURRENT_INTERSTAGE 1
CURRENT_PAYLOAD 1
FAIRING 1
MET -20
GNC_RUN 0
STAGE_IGNITION_TIME 0.000000
STAGE_STATE 1
ALT_STEPS 100.0,350.0,1400.0,35000.0
PEG_PITCH_LIMIT 35.000
PEG_MC_INTERVAL 0.100
END
ProtonTrain:spacecraft\spacecraft3
STATUS Landed Earth
POS 62.9847639 46.0708662
HEADING 27.15
ALT -0.000
AROT 97.933 32.494 -41.376
ATTACHED 0:1,Socle
AFCMODE 7
NAVFREQ 0 0
RCS 1
CTRL_SURFACE 1
CONFIGURATION 1
CURRENT_PAYLOAD 0
SEQ 0 2 0.186530
SEQ 1 -2 0.000000
SEQ 2 -2 0.000000
SEQ 3 -2 1.000000
END
ProtonTower:spacecraft\spacecraft3
STATUS Landed Earth
POS 62.9847639 46.0708662
HEADING 27.15
ALT -0.000
AROT 97.933 32.494 -41.376
ATTACHED 0:0,Socle
AFCMODE 7
NAVFREQ 0 0
CONFIGURATION 1
CURRENT_PAYLOAD 0
SEQ 0 2 0.356375
SEQ 1 2 1.000000
SEQ 2 -2 0.000000
SEQ 3 -2 0.000000
SEQ 4 -2 0.000000
SEQ 5 -2 0.000000
SEQ 6 -2 0.000000
SEQ 7 -2 0.000000
SEQ 8 -2 0.000000
SEQ 9 -2 0.000000
SEQ 10 -2 0.000000
END
ProtonLights:spacecraft\spacecraft3
STATUS Landed Earth
POS 62.9847639 46.0708662
HEADING 27.15
ALT -0.000
AROT 97.933 32.494 -41.376
ATTACHED 0:2,Socle
AFCMODE 7
PRPLEVEL 0:1.000000
NAVFREQ 0 0
CONFIGURATION 1
CURRENT_PAYLOAD 0
END
MS_LaunchPad_ProtonK:Ghost_PAD24
STATUS Landed Earth
POS 62.9847654 46.0709434
HEADING 359.68
ALT -0.011
AROT 49.364 -18.369 160.157
ATTACHED 0:0,ProtonTrain
AFCMODE 7
NAVFREQ 0 0
END
MS_LaunchPad_Socle:EmptyModule
STATUS Landed Earth
POS 62.9847639 46.0708662
HEADING 360.00
ALT -0.011
AROT 49.364 -18.369 159.837
AFCMODE 7
NAVFREQ 0 0
END
Socle:Socle24\Socle24
STATUS Landed Earth
POS 62.9847639 46.0708662
HEADING 0.00
ALT -0.001
AROT 49.364 -18.369 159.837
ATTACHED 0:0,MS_LaunchPad_Socle
AFCMODE 7
NAVFREQ 0 0 0 0
XPDR 0
CONFIG_FILE Config\Socle24\socle24.ini
CONFIGURATION 0
CURRENT_BOOSTER 1
CURRENT_STAGE 1
CURRENT_INTERSTAGE 1
CURRENT_PAYLOAD 1
FAIRING 0
MET 0.000
STAGE_IGNITION_TIME 0.000000
STAGE_STATE 1
ALT_STEPS 100.0,350.0,1400.0,35000.0
PEG_PITCH_LIMIT 35.000
PEG_MC_INTERVAL 0.100
RAMP
END

 

[ovrocm]

What version of Orbiter are you using?

Orbiter 2016, according to the document, it is supposed to be compatible.

Pack by Papyref for Orbiter 2016
Corrected April 2018

---------- Post added at 06:11 PM ---------- Previous post was at 06:08 PM ----------

proton ready to launch (no train)

Thank you.