Project SpaceX SuperHeavy

[gattispilot]

Thanks. So I just added an adapter mesh and adjust the Starship

 

[gattispilot]

I wonder about these 4 structures? I wonder if they would extend out? They look like maybe dock ports for a tanker?
nose open and payload slot open.

I wonder what the sats would look like?

 

[diogom]

Yes probe and drogue docking ports for prop transfer. These are drogues, nothing else has been seen yet.

StarshipGazer will be your friend for visuals

 

[gattispilot]

Thanks. I will extend them more so that they will be level with the surface just past those pipes

 

[gattispilot]

Hmm. So basically I took a Version3 mesh and changed the animation,.....

But I wonder why the booster did not land at the tower?
Starship_Booster:spacex_starship/spacex_boostervers3
STATUS Landed Earth
POS -97.1211236 25.9951563
HEADING 55.32
ALT 34.762
AROT 153.833 6.401 -58.451
AFCMODE 7
PRPLEVEL 0:0.019251
NAVFREQ 0 0
FINS 0 0.0000 0.5000 0.5000
APST 2 0 0 0 0 0 0 0.0000 1 0
LPRM BC_TOWER
END
BC_TOWER:spacex_starship\bc_tower
STATUS Orbiting Earth
RPOS -2626104.208 544053.671 5777596.661
RVEL -369.8362 76.8261 -177.8347
AROT 155.560 65.697 -116.726
AFCMODE 7
NAVFREQ 0 0
ARMSTS 0 2 0 2
ARMPRC 0.500 1.000 0.000 0.000 1.000 0.000
PRMS 10.000 1.000 0 0
CLAW 2 1.000 0.986 0.767
PSTN 0.997 0.828
STTS 0 0 1 1 0.0
TRGT AUTO
END
I wonder why the BC_Tower is not landed it starts out that way?
BC_TOWER:spacex_starship\bc_tower
STATUS Landed Earth
POS -97.1540880 25.9953540
HEADING 90.00
ALT 0.5
AROT 180.000 -82.846 -115.995
AFCMODE 7
NAVFREQ 0 0
ARMSTS 0 2 0 0
ARMPRC 0.500 1.000 0.000 0.000 0.000 1.000
PRMS 10.000 1.000 0
CLAW 0 0.000 0.000 1.000
PSTN 0.013 0.067
STTS 0 1 0 0 0.0
TRGT AUTO
END

 

[gattispilot]

I turned off attachment manager and ran a sample scn.
And the booster was closer.
BC_TOWER:spacex_starship\bc_tower
STATUS Landed Earth
POS -97.1540880 25.9953540
HEADING 90.00
ALT 0.500
AROT 180.000 -82.846 -115.995
AFCMODE 7
NAVFREQ 0 0
ARMSTS 0 2 0 2
ARMPRC 0.500 1.000 0.000 0.000 1.000 0.000
PRMS 10.000 1.000 0 0
CLAW 2 1.000 0.986 0.767
PSTN 0.997 0.828
STTS 0 0 1 1 0.0
TRGT AUTO
END
BC_PAD:spacex_starship\bc_pad
STATUS Landed Earth
POS -97.1567080 25.9965440
HEADING 90.00
ALT 3.000
AROT 180.000 -82.843 -115.997
AFCMODE 7
NAVFREQ 0 0
STTS 0 0 0 0.0
END
Starship_Booster:spacex_starship/spacex_booster
STATUS Landed Earth
POS -97.1541381 25.9954528
HEADING 222.44
ALT 34.766
AROT 153.906 6.506 -47.244
AFCMODE 7
PRPLEVEL 0:0.002952
NAVFREQ 0 0
FINS 0 0.0000 0.5000 0.5000
APST 2 0 0 0 0 0 0 0.0000 1 0
LPRM BC_TOWER
END

 

[gattispilot]

I loaded a starlink sat into her. I need to figure how to do multiple sat. The attachments need to move along the z axis.

 

[gattispilot]

I am searching for a flight profile for Starship to launch the satellites.

Right now it has the ability to launch 1. I need to figure out how to move the attachments up.

Not sure why the bC tower sometimes is landed and sometimes orbiting.

 

[gattispilot]

I can load more than 1 starlink sat in my version3. Right now as the attachment position is the same they all load there. Otherwise You would need to move an attachment point and sat up to the slot.

But not sure on the orbit and flight profile:https://www.spacex.com/launches/starship-flight-12

The other thing I have been asked is frost on the ship. I suppose just a frost mesh could be added on top and then removed?

 

[gattispilot]

This is what I have so far. She will launch. But not sure on the orbit for launch sats and landing.

For the Sats. I am using this:

Addon icon B

Starlink

May 26, 2019

Imported from OHM

• BrianJ
• Spacecraft

But I changed the cfg to add another attachment for the Starship.
P opens the Sat hatch and W opens the nose cone for docking

 

[drewski_505]

How can I change the orientation of the Starlink?